Skip to content

Urgent: Nov 20, 2026 — HCS 2024 Deadline. Get ready →

PPE and the bodyAbout 5 minutes29 CFR 1926.102 · 1910.133

Eye Protection Toolbox Talk

A short talk on eye protection: which hazards call for safety glasses, which call for goggles, when a face shield goes over them, and what to do in the first seconds after a splash. In construction, the employer shall ensure that each affected employee uses appropriate eye or face protection against flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, and injurious light radiation (29 CFR 1926.102(a)(1)).

All safety topics

At a glance

  • Construction: 29 CFR 1926.102. General industry: 29 CFR 1910.133. Devices meet ANSI Z87.1 (1989 R-1998, 2003 or 2010 edition) or are shown to be as effective.
  • About 5 minutes to read the script out loud, then the three questions. The drill and the tables below add time if you use them.
  • FY2025 citations: 29 CFR 1926.102, 2,600 (2,572 at construction sites); 29 CFR 1910.133, 492 (8 at construction sites).
  • Free PDF and Word file: the script, the questions, the rule and a 20-line sign-in sheet. No account, no email.

Read this to your crew

Today is about eyes. On a job, an eye injury can start with something small: a chip off a grinder, a splash when a hose comes loose, dust blown off a beam. It takes a second.

Match the protection to what can reach your eyes. Safety glasses with side protection stop chips coming from the front and the sides. Goggles seal around the eyes, so they are what you wear for splashes, fine dust and anything that can come up from below or around a frame. A face shield protects your face from splashes and sparks, but on its own it does not stop a flying chip: it goes over glasses or goggles, never instead of them.

If you wear prescription glasses, they are not safety glasses unless they were made as safety glasses. Wear safety eyewear made with your prescription, or goggles or over-glasses that fit over your own glasses without pushing them out of place.

Welding and cutting need a filter lens with the right shade for the process. The shade depends on the operation and the electrode or the metal, so look it up for the job instead of grabbing whatever helmet is on the truck. People working near the welder need protection from the light too.

Look at your eye protection before you put it on: cracked or deeply scratched lenses, a loose side shield, a goggle strap that no longer holds. Damaged eyewear gets replaced, not taped.

Know where the eyewash is before you open a chemical. If something gets in your eyes, go straight there, hold your eyelids open and keep flushing for as long as Section 4 of the product's safety data sheet says, then get medical help. Do not rub.

Three questions for the crew

  1. Which task today could send something into your eyes, and which protection does it call for?
    Listen for: A named task and a matching choice: glasses with side protection for chips, goggles for splashes and fine dust, a face shield over them for grinding or pouring.
  2. Where is the nearest eyewash, and is the path to it clear right now?
    Listen for: The exact location, and a path with nothing in the way today.
  3. When is a face shield enough by itself?
    Listen for: Never against flying chips. It goes over safety glasses or goggles.

What are OSHA's rules for eye and face protection?

In construction, the employer shall ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation (29 CFR 1926.102(a)(1)). Where there is a hazard from flying objects, the protection must provide side protection (29 CFR 1926.102(a)(2)), and an employee who wears prescription lenses must wear protection that incorporates the prescription or fits over it without disturbing it (29 CFR 1926.102(a)(3)).

Protective eye and face devices must comply with ANSI/ISEA Z87.1-2010, ANSI Z87.1-2003 or ANSI Z87.1-1989 (R-1998) (29 CFR 1926.102(b)(1)), or the employer must demonstrate that they are at least as effective (29 CFR 1926.102(b)(2)). The rule names those editions; a newer edition of Z87.1 is a consensus standard, not an OSHA rule by itself.

General industry has the same duties in 29 CFR 1910.133(a)(1) to (a)(3) and the same list of editions in 29 CFR 1910.133(b). Where the eyes or body of any person may be exposed to injurious corrosive materials, suitable facilities for quick drenching or flushing of the eyes and body shall be provided within the work area for immediate emergency use (29 CFR 1926.50(g) in construction, 29 CFR 1910.151(c) in general industry).

The paragraphs, word for word:

“(a) General. (1) The employer shall ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation.”

29 CFR 1926.102(a)(1)

“(2) The employer shall ensure that each affected employee uses eye protection that provides side protection when there is a hazard from flying objects. Detachable side protectors (e.g. clip-on or slide-on side shields) meeting the pertinent requirements of this section are acceptable.”

29 CFR 1926.102(a)(2)

“(3) The employer shall ensure that each affected employee who wears prescription lenses while engaged in operations that involve eye hazards wears eye protection that incorporates the prescription in its design, or wears eye protection that can be worn over the prescription lenses without disturbing the proper position of the prescription lenses or the protective lenses.”

29 CFR 1926.102(a)(3)

How often did OSHA cite these rules in FY2025?

StandardConstruction sitesOther industriesAll FY2025 citations
29 CFR 1926.102Eye and face protection, constructionParagraph 1926.102(a)(1): 2,555 of these2,572282,600
29 CFR 1910.133Eye and face protection, general industry8484492

Citation items under 29 CFR issued Oct 1, 2024 to Sep 30, 2025, at federal and State Plan inspections, counted by HazComFast on U.S. Department of Labor enforcement data (extracted Oct 13, 2026). Construction means an inspection whose NAICS code starts with 23. The counts describe inspected establishments, not every employer.

Which eye protection for which task?

TaskHazardProtectionLimit
GrindingChips and sparks at high speedSafety glasses with side protection, and a face shield over themA face shield alone does not stop a flying chip
Cutting with a sawChips and dustSafety glasses with side protection; goggles when fine dust gets around the frameDust behind your glasses means goggles
Drilling overheadFalling dust and chipsGogglesGlasses leave the top of the eye open
Pouring or mixing chemicalsSplashesChemical splash goggles, and a face shield over them when you pourGoggles with open vents made for impact do not seal out liquids
Welding and cuttingLight radiation, sparks and spatterA helmet or goggles with the filter shade for the process, over safety glassesOne shade does not fit every process; Table E-1 of 29 CFR 1926.102(c)(1) is the guide

Eye and face protection is marked to identify its maker, and devices built to ANSI Z87.1 carry the Z87 mark.

Check before use, replace when damaged

  • Lenses: no cracks, deep scratches or pits in the line of sight.
  • Frames and side shields: not bent, side shields in place.
  • Goggles: the seal sits flat on the face, and the strap still holds.
  • Face shields: the window is clear and the headgear locks.
  • Fit: glasses that slide down get adjusted or replaced; fogging goggles get an anti-fog lens or a better fit, not a lift off the face.
  • Care: clean and store each item the way its maker says, in a case or bag away from tools.

Drill: the first seconds after a splash

About five minutes, with no chemical in use and nobody's eyes exposed to anything.

  1. Start at the spot where the crew mixes or pours today, and walk to the eyewash or the flushing station. Note how long it takes and what is in the way.
  2. Open the eyewash and check that clean water flows from both nozzles.
  3. Show how to hold the eyelids open with the fingers while flushing.
  4. Read Section 4 of the safety data sheet for the product used today, out loud: how long to flush and when to get medical help.
  5. Name who calls for help and who stays with the worker.

Inside HazComFast

Give the eye protection talk, keep every signature

Print this talk for the morning meeting. In HazComFast, the crew signs the toolbox talk on a phone, in English or Spanish, and the record stays with each worker.

  • Signed where the signal isn't

    In a basement or a dead zone, the crew can still sign the toolbox talk in Chrome on Android or on a computer. The sign-ins go out once the app is open with a signal again, and each one lands once.
  • Sheets and certificates in Spanish

    Toolbox talk PDFs and training certificates print in Spanish, and compliance reports come out in English, Spanish or both side by side.
  • Thirty hires on a Monday morning

    Import a spreadsheet, see line by line who was created and who wasn't, and print one sheet of QR badges for the morning toolbox talk. Email is optional.
  • Records that stay when a worker leaves

    When a worker leaves, their training records and competent person designation stay on file. The account can't take them along.

New sign-ups are paused · the free tools need no account

Questions about this talk

Are prescription glasses enough eye protection?

Not unless they are made as safety eyewear. In construction, an employee who wears prescription lenses during operations with eye hazards must wear eye protection that incorporates the prescription, or protection that fits over the prescription lenses without disturbing them (29 CFR 1926.102(a)(3)). General industry has the same rule (29 CFR 1910.133(a)(3)).

Is a face shield enough eye protection?

Not against impact. OSHA's personal protective equipment guide says face shields protect against splashes and sprays but will not provide adequate protection against impact hazards, and that face shields used with goggles or safety spectacles provide additional protection (OSHA 3151). Wear the shield over safety glasses or goggles.

Which ANSI standard does OSHA require for safety glasses?

The construction rule lists ANSI/ISEA Z87.1-2010, ANSI Z87.1-2003 and ANSI Z87.1-1989 (R-1998) (29 CFR 1926.102(b)(1)), and accepts devices the employer demonstrates to be at least as effective (29 CFR 1926.102(b)(2)). General industry lists the same editions (29 CFR 1910.133(b)).

Who pays for safety glasses?

The employer provides the protective equipment at no cost to employees, with the exceptions the rule lists (29 CFR 1926.95(d)(1)). One exception is non-specialty prescription safety eyewear that the employer permits employees to wear off the job site (29 CFR 1926.95(d)(4)(i)).

How long should you flush an eye after a chemical splash?

As long as Section 4 of the product's safety data sheet says, then get medical help. Where corrosive materials can reach the eyes, suitable facilities for quick drenching or flushing are provided within the work area (29 CFR 1926.50(g); 29 CFR 1910.151(c)).

Does OSHA require toolbox talks?

No rule requires a talk by that name. Construction employers must instruct each employee in the recognition and avoidance of unsafe conditions (29 CFR 1926.21(b)(2)), and many standards carry their own training duty; a toolbox talk is a common way to deliver part of it.

Do we need a sign-in sheet for a toolbox talk?

No general OSHA rule requires attendance records for a toolbox talk. Some standards require written certification of training, such as fall protection (29 CFR 1926.503(b)(1)) and forklift operators (29 CFR 1910.178(l)(6)). A signed sheet shows who attended; keep the topic, the date, the presenter and the language with it. It does not show that the content was understood.

Go further

More talks on ppe and the body

Sources

In a State Plan state, the state's own standard applies, and it can be stricter than the federal rule. Not legal advice.

All safety topics 100 safety topics Safety tip of the day