Skip to content

Urgent: Nov 20, 2026 — HCS 2024 Deadline. Get ready →

Machines, tools and energyAbout 7 minutes29 CFR 1926.300 · 1926.303

Angle Grinder Safety Toolbox Talk

A short talk on angle grinders: matching the disc to the grinder, grinding and cutting as two different jobs, the guard made for the disc, kickback, sparks, and eye protection. In construction, portable abrasive wheels used for external grinding shall be provided with safety guards (29 CFR 1926.303(c)(3)), and employees using abrasive wheels shall be protected by eye protection (29 CFR 1926.303(c)(9)).

All safety topics

At a glance

  • Construction: tools kept in a safe condition (29 CFR 1926.300(a)); guards on portable abrasive wheels (29 CFR 1926.303(c)(3) and (c)(5)); wheels inspected and ring-tested before mounting (29 CFR 1926.303(c)(7)); eye protection (29 CFR 1926.303(c)(9)).
  • About 7 minutes to read the script out loud, then the three questions. The drill and the tables below add time if you use them.
  • FY2025 citations: 29 CFR 1926.303, 34 (30 at construction sites); 29 CFR 1926.300, 149 (140 at construction sites).
  • Free PDF and Word file: the script, the questions, the rule and a 20-line sign-in sheet. No account, no email.

Read this to your crew

Today is the angle grinder. Grinding, cutting, polishing and wire wheels can throw off flying fragments, and OSHA's hand and power tools booklet warns that an abrasive wheel may disintegrate or explode during start-up.

Start with the disc. Its rated speed is equal to or higher than the maximum speed marked on the grinder, its size is within what the grinder takes, and it is a type the grinder's maker specifies. A wheel worn down on a bigger grinder does not go on a smaller one: it is not made for the higher speed.

Grinding and cutting are different jobs. A cutoff wheel cuts with its edge. Do not grind with the side of a cutoff wheel: side forces can make it shatter. Cutoff wheels can need different flanges and a different guard than grinding wheels, and the manual says which.

Look the disc over for chips and cracks before each use, and check any disc or grinder that was dropped. Check the disc the way its maker's instructions say for that type of disc. It fits freely on the spindle, is never forced on, and the nut is tightened only enough to hold it. Unplug the grinder or take the battery out before changing a disc.

The guard made for that disc stays on, secured and turned so that the least amount of disc faces you. It holds back fragments if a disc breaks, and the sparks that could set clothing on fire. If the guard is in the way, change the tool or the method, never the guard.

Kickback is the grinder's sudden reaction when the disc pinches or snags: the tool is thrown the opposite way, toward you or away from you. Hold it firmly with both hands, use the side handle, keep your hand away from the spinning disc, and keep your body out of the path the grinder would take if it kicked back. Corners, sharp edges and bouncing the disc can make it snag.

Clamp the work so both hands stay on the grinder. Let it reach full speed before it touches the work, and never stand in the disc's plane of rotation while it speeds up. Before the first spark, look where the sparks will go: nothing flammable near them, and nobody close who is not part of the job.

Wear safety glasses or goggles every time, with a face shield over them when the task calls for it, and hearing protection and a dust mask as appropriate. Never set the grinder down until the disc has stopped, and turn the power off when it is not in use.

Three questions for the crew

  1. What has to match before a disc goes on the grinder?
    Listen for: A rated speed equal to or higher than the grinder's maximum speed, a size within the grinder's capacity, a type the maker specifies, and the guard made for it.
  2. Can you grind with the side of a cutoff wheel?
    Listen for: No. A cutoff wheel cuts with its edge; side forces can make it shatter.
  3. Where do you keep your body, and what do you do if the wheel binds in a cut?
    Listen for: Out of the disc's plane of rotation and out of the path of a kickback; switch off and hold the grinder still until the wheel stops.

What are OSHA's rules for grinders?

In construction, all hand and power tools and similar equipment, whether furnished by the employer or the employee, shall be maintained in a safe condition (29 CFR 1926.300(a)), and power operated tools designed to accommodate guards shall be equipped with such guards when in use (29 CFR 1926.300(b)(1)).

Portable abrasive wheels used for external grinding shall be provided with safety guards, with narrow exceptions (29 CFR 1926.303(c)(3)). The guard is mounted in alignment with the wheel, strong enough to retain fragments if the wheel breaks, and exposes no more than 180 degrees of the wheel (29 CFR 1926.303(c)(5)).

All abrasive wheels shall be closely inspected and ring-tested before mounting (29 CFR 1926.303(c)(7)). Grinding wheels shall fit freely on the spindle and shall not be forced on, and the spindle nut shall be tightened only enough to hold the wheel in place (29 CFR 1926.303(c)(8)). All employees using abrasive wheels shall be protected by eye protection (29 CFR 1926.303(c)(9)).

The grinder maker's safety warnings add the rest: the accessory types and guards for each tool, the start-up check, and the warnings on kickback and cutting.

The paragraphs, word for word:

“(7) All abrasive wheels shall be closely inspected and ring-tested before mounting to ensure that they are free from cracks or defects.”

29 CFR 1926.303(c)(7)

“(8) Grinding wheels shall fit freely on the spindle and shall not be forced on. The spindle nut shall be tightened only enough to hold the wheel in place.”

29 CFR 1926.303(c)(8)

How often did OSHA cite these rules in FY2025?

StandardConstruction sitesOther industriesAll FY2025 citations
29 CFR 1926.303Abrasive wheels and toolsParagraph 1926.303(c): 8 of these30434
29 CFR 1926.300Hand and power tools, general requirementsParagraph 1926.300(b)(1): 63 of these1409149

Citation items under 29 CFR issued Oct 1, 2024 to Sep 30, 2025, at federal and State Plan inspections, counted by HazComFast on U.S. Department of Labor enforcement data (extracted Oct 13, 2026). Construction means an inspection whose NAICS code starts with 23. The counts describe inspected establishments, not every employer.

Before the grinder starts

CheckWhat it meansSource
Disc speedThe disc's rated speed is equal to or higher than the maximum speed marked on the grinderGrinder maker's warnings; OSHA 3080
Disc size and typeWithin the grinder's capacity, a type the maker specifies, never a wheel worn down on a larger grinderGrinder maker's warnings
Disc conditionNo chips or cracks; inspected and ring-tested before mounting, and checked the way the disc maker says29 CFR 1926.303(c)(7); disc maker
MountingFits freely, never forced; nut only tight enough to hold it; undamaged flanges of the right size and shape29 CFR 1926.303(c)(8); grinder maker's warnings
GuardThe guard made for that disc type, secured, with the least amount of disc facing the operator29 CFR 1926.303(c)(3) and (c)(5); grinder maker's warnings
AreaNothing flammable where the sparks will go; people not part of the job at a safe distanceGrinder maker's warnings; OSHA 3080
ProtectionSafety glasses or goggles with side protection; a face shield over them, hearing protection and a dust mask as the task calls for29 CFR 1926.102(a)(2); OSHA 3151; grinder maker's warnings

OSHA 3080 is OSHA's Hand and Power Tools booklet and OSHA 3151 its Personal Protective Equipment booklet. The grinder maker's warnings come from the Bosch angle grinder instructions listed in the sources; the manual of the grinder in use has the last word.

The start-up check in the grinder's manual

Follow the start-up check in the manual of the grinder in use. Bosch's, for example, has the operator inspect the accessory, mount it, move everyone out of the plane of the rotating accessory, and run the grinder at maximum no-load speed for one minute, because a damaged accessory will normally break apart during that time.

When the job is cutting

The grinder maker's warnings for cutoff wheels:

  • Do not jam the cutoff wheel, push too hard or try a cut that is too deep.
  • Do not stand in line with and behind the turning wheel.
  • If the wheel binds, or the cut stops for any reason, switch off and hold the grinder still until the wheel stops. Never pull the wheel out of the cut while it turns.
  • Restart outside the work piece, let the wheel reach full speed, then carefully re-enter the cut.
  • Support panels and large pieces near the line of cut and near the edge, on both sides of the wheel.
  • Take extra care with a pocket cut into a wall: the wheel can cut gas or water pipes or electrical wiring.
  • Do not try curved cuts.

Drill: choose the disc without spinning anything

About five minutes, with the grinder unplugged or the battery out and no disc mounted.

  1. Lay out the grinder, its manual and the discs from the truck.
  2. Read the maximum speed marked on the grinder and the rated speed and size on each disc. Set aside any disc rated slower or sized beyond the grinder's capacity.
  3. For today's task, the crew picks the disc and says whether the job is grinding or cutting.
  4. Find in the manual the guard and the flanges for that disc.
  5. Look the chosen discs over for chips and cracks.
  6. Name what near today's work could catch a spark, and where the people not part of the job will be.

Grinding concrete, block or stone

Table 1 of the construction silica standard has two lines for handheld grinders. For mortar removal, it lists a grinder with a commercially available shroud and dust collection system, plus a respirator. For other uses, it lists a grinder with an integrated water delivery system, outdoors only, or a grinder with a shroud and dust collection system.

For each employee engaged in a task identified on Table 1, the employer shall fully and properly implement the controls specified for the task, unless the employer assesses and limits the exposure under paragraph (d) (29 CFR 1926.1153(c)(1)).

Inside HazComFast

Give the grinder talk, keep every signature

Print this talk for the morning meeting. In HazComFast, the crew signs the toolbox talk on a phone, in English or Spanish, and the record stays with each worker.

  • Signed where the signal isn't

    In a basement or a dead zone, the crew can still sign the toolbox talk in Chrome on Android or on a computer. The sign-ins go out once the app is open with a signal again, and each one lands once.
  • Sheets and certificates in Spanish

    Toolbox talk PDFs and training certificates print in Spanish, and compliance reports come out in English, Spanish or both side by side.
  • Thirty hires on a Monday morning

    Import a spreadsheet, see line by line who was created and who wasn't, and print one sheet of QR badges for the morning toolbox talk. Email is optional.
  • Records that stay when a worker leaves

    When a worker leaves, their training records and competent person designation stay on file. The account can't take them along.

New sign-ups are paused · the free tools need no account

Questions about this talk

Can you remove the guard on an angle grinder?

Not to make a job easier. In construction, power operated tools designed to accommodate guards shall be equipped with such guards when in use (29 CFR 1926.300(b)(1)), and portable abrasive wheels used for external grinding shall be provided with safety guards (29 CFR 1926.303(c)(3)).

Does OSHA require a ring test for grinder discs?

The construction rule says all abrasive wheels shall be closely inspected and ring-tested before mounting to ensure that they are free from cracks or defects (29 CFR 1926.303(c)(7)). OSHA's Hand and Power Tools booklet describes the test as tapping the wheel gently with a light, non-metallic instrument, and says not to use a wheel that sounds cracked or dead. Follow the disc maker's instructions for checking that type of disc.

What is kickback on an angle grinder?

In the grinder maker's words, kickback is a sudden reaction to a pinched or snagged rotating wheel or other accessory: the tool is forced in the direction opposite to the accessory's rotation, and the wheel can jump toward or away from the operator. The warnings call for a firm grip with both hands, the auxiliary handle, and the body kept out of the area where the tool would move.

Why can a grinder disc break?

OSHA's Hand and Power Tools booklet points to a wheel that is cracked or sounds dead when tapped, a wheel that does not fit freely on the spindle, and a machine running faster than the speed marked on the wheel, and warns that an abrasive wheel may disintegrate or explode during start-up. The grinder maker's warnings add side forces on a cutoff wheel and a wheel worn down on a larger grinder.

What eye protection do you need for grinding?

Employees using abrasive wheels shall be protected by eye protection (29 CFR 1926.303(c)(9)), and the employer shall ensure that each affected employee uses eye protection that provides side protection when there is a hazard from flying objects (29 CFR 1926.102(a)(2)). OSHA's PPE booklet adds that a face shield alone does not protect against impact; worn with goggles or safety glasses, it adds protection.

Does grinding concrete fall under the silica standard?

Table 1 of 29 CFR 1926.1153 lists handheld grinders, for mortar removal and for other uses, with the controls for each. For each employee engaged in a task on Table 1, the employer shall fully and properly implement the specified controls, unless the employer assesses and limits the exposure under paragraph (d) (29 CFR 1926.1153(c)(1)).

Does OSHA require toolbox talks?

No rule requires a talk by that name. Construction employers must instruct each employee in the recognition and avoidance of unsafe conditions (29 CFR 1926.21(b)(2)), and many standards carry their own training duty; a toolbox talk is a common way to deliver part of it.

Do we need a sign-in sheet for a toolbox talk?

No general OSHA rule requires attendance records for a toolbox talk. Some standards require written certification of training, such as fall protection (29 CFR 1926.503(b)(1)) and forklift operators (29 CFR 1910.178(l)(6)). A signed sheet shows who attended; keep the topic, the date, the presenter and the language with it. It does not show that the content was understood.

Go further

More talks on machines, tools and energy

Sources

In a State Plan state, the state's own standard applies, and it can be stricter than the federal rule. Not legal advice.

All safety topics 100 safety topics Safety tip of the day