Skip to content

Urgent: Nov 20, 2026 — HCS 2024 Deadline. Get ready →

Machines, tools and energyAbout 5 minutes29 CFR 1926.302(c)(1) · 1910.266(e)(2)

Chainsaw Safety Toolbox Talk

A short talk on chainsaws for crews that cut brush, limbs, posts or storm debris on a jobsite: the check before starting, fueling and starting, both hands on the saw, footing, wood under tension, and protective gear. OSHA's logging standard applies to logging operations; its chain saw rules sit here next to the construction rules as the reference for safe cutting. Felling trees, cutting wood under tension, work near power lines and climbing are outside this talk.

All safety topics

At a glance

  • Construction: tools kept in a safe condition (29 CFR 1926.300(a)); fuel powered tools stopped while refueled, serviced or maintained (29 CFR 1926.302(c)(1)). Logging operations: chain saw rules in 29 CFR 1910.266(e)(2).
  • About 5 minutes to read the script out loud, then the three questions. The drill and the tables below add time if you use them.
  • Free PDF and Word file: the script, the questions, the rule and a 20-line sign-in sheet. No account, no email.

Read this to your crew

Today is the chainsaw, for brush, limbs, posts and cleanup on the ground. Felling trees, wood under tension, work near power lines and climbing are outside this talk; they take training and equipment beyond it.

Check the saw against its manual before you start it. OSHA's logging standard has every chain saw operated and adjusted the way the manufacturer's instructions say, and it forbids removing or disabling any kickback device. Saws placed into service after that rule took effect have a chain brake. On a gasoline saw, letting go of the throttle stops the chain.

Fuel the saw with the engine stopped, 10 feet or more from any flame or other source of ignition, and start it 10 feet or more from where you fueled. Start it on the ground or firmly supported, with the chain brake engaged. Never drop start it.

Hold it with the thumbs and fingers of both hands wrapped around the handles. Be sure of your footing before you cut, and never cut from a spot where you could lose your balance, your footing or your grip. Do not cut directly overhead, and carry the saw so that you cannot touch the chain or the muffler.

Keep everyone who is not part of the job at a safe distance. Watch for spring poles: a tree, limb or sapling held under tension by the weight of something else. Those cuts are outside this crew's work today.

The logging standard lists the gear for chain saw work: cut-resistant leg protection from the thigh to the top of the boot, cut-resistant foot protection, head protection where things can fall or fly, and eye protection, with face protection where the face can be hurt. On a construction site, protective equipment is used wherever the hazards call for it.

Stop the engine before you refuel, adjust, sharpen or clear the chain.

Three questions for the crew

  1. What do you check before starting the saw?
    Listen for: The saw against its manual, the chain brake or other kickback device in place, and a throttle that stops the chain when released.
  2. Where and how do you start the saw?
    Listen for: 10 feet or more from where it was fueled, on the ground or firmly supported, with the chain brake engaged. Never drop started.
  3. Which cuts do we leave to someone trained for them?
    Listen for: Felling trees, spring poles and other wood under tension, anything near power lines, and climbing work.

Which rules apply to chainsaws on a construction site?

In construction, all hand and power tools and similar equipment, whether furnished by the employer or the employee, shall be maintained in a safe condition (29 CFR 1926.300(a)), and all fuel powered tools shall be stopped while being refueled, serviced, or maintained (29 CFR 1926.302(c)(1)). Protective equipment shall be provided, used, and maintained wherever it is necessary by reason of hazards (29 CFR 1926.95(a)).

The logging standard applies to all logging operations as defined by that section (29 CFR 1910.266(b)(2)). Its chain saw rules are written for logging.

In logging, each chain saw placed into initial service after the section took effect shall be equipped with a chain brake, and no chain-saw kickback device shall be removed or otherwise disabled (29 CFR 1910.266(e)(2)(i)). The chain saw shall be fueled at least 10 feet from any open flame or other source of ignition (29 CFR 1910.266(e)(2)(iv)) and started at least 10 feet from the fueling area (29 CFR 1910.266(e)(2)(v)).

The chain saw shall be started on the ground or where otherwise firmly supported (29 CFR 1910.266(e)(2)(vi)), with the chain brake engaged (29 CFR 1910.266(e)(2)(vii)), and held with the thumbs and fingers of both hands encircling the handles, unless the employer shows that a greater hazard is posed in that situation (29 CFR 1910.266(e)(2)(viii)).

Each employee who operates a chain saw in logging wears leg protection constructed with cut-resistant material, covering the full length of the thigh to the top of the boot, provided at no cost to the employee (29 CFR 1910.266(d)(1)(iv)).

The paragraphs, word for word:

“(c) Fuel powered tools. (1) All fuel powered tools shall be stopped while being refueled, serviced, or maintained, and fuel shall be transported, handled, and stored in accordance with subpart F of this part.”

29 CFR 1926.302(c)(1)

“(v) The chain saw shall be started at least 10 feet (3 m) from the fueling area.”

29 CFR 1910.266(e)(2)(v)

Pre-start check

CheckWhat to look forSource
ManualThe saw is set up and adjusted the way its manual says29 CFR 1910.266(e)(2)(iii)
Kickback deviceChain brake or other kickback device in place, never removed or disabled29 CFR 1910.266(e)(2)(i)
ThrottleOn a gasoline saw, releasing the throttle stops the chain29 CFR 1910.266(e)(2)(ii)
FuelingEngine stopped, 10 feet or more from any flame or other source of ignition29 CFR 1926.302(c)(1); 29 CFR 1910.266(e)(2)(iv)
Starting10 feet or more from the fueling area, on the ground or firmly supported, chain brake engaged29 CFR 1910.266(e)(2)(v); 29 CFR 1910.266(e)(2)(vi); 29 CFR 1910.266(e)(2)(vii)
Protective gearCut-resistant leg and foot protection, head protection, eye and face protection29 CFR 1910.266(d)(1)(iv) to (vii)

The logging standard's rules apply to logging operations; on a construction site, they are a reference next to the saw's manual.

Drill: plan the cut with the engine off

About five minutes at the pile or the limb to be cut. Nothing runs during the drill.

  1. Look for spring poles and other wood under tension: limbs or saplings bent under the weight of something else, a log that can roll or slide.
  2. Decide where each piece will fall or roll, and mark the zone nobody enters while the saw runs.
  3. Run the pre-start check with the engine off.
  4. Point to the fueling spot, and to the starting spot 10 feet or more away from it.
  5. Name what goes to a trained crew instead: felling, wood under tension, anything near power lines.

Inside HazComFast

Give the chainsaw talk, keep every signature

Print this talk for the morning meeting. In HazComFast, the crew signs the toolbox talk on a phone, in English or Spanish, and the record stays with each worker.

  • Signed where the signal isn't

    In a basement or a dead zone, the crew can still sign the toolbox talk in Chrome on Android or on a computer. The sign-ins go out once the app is open with a signal again, and each one lands once.
  • Sheets and certificates in Spanish

    Toolbox talk PDFs and training certificates print in Spanish, and compliance reports come out in English, Spanish or both side by side.
  • Thirty hires on a Monday morning

    Import a spreadsheet, see line by line who was created and who wasn't, and print one sheet of QR badges for the morning toolbox talk. Email is optional.
  • Records that stay when a worker leaves

    When a worker leaves, their training records and competent person designation stay on file. The account can't take them along.

New sign-ups are paused · the free tools need no account

Questions about this talk

Does OSHA's logging standard apply to chainsaw use on a construction site?

The logging standard applies to logging operations as defined in that section (29 CFR 1910.266(b)(2)). On a construction site, the construction rules apply, such as tools maintained in a safe condition (29 CFR 1926.300(a)) and fuel powered tools stopped while refueled, serviced or maintained (29 CFR 1926.302(c)(1)), along with the saw maker's manual.

Do chainsaw operators need leg protection?

In logging, yes: each employee who operates a chain saw wears leg protection constructed with cut-resistant material, covering the full length of the thigh to the top of the boot, provided at no cost (29 CFR 1910.266(d)(1)(iv)). In construction, protective equipment shall be provided, used, and maintained wherever it is necessary by reason of hazards (29 CFR 1926.95(a)).

Can you refuel a running chainsaw?

No. In construction, all fuel powered tools shall be stopped while being refueled, serviced, or maintained (29 CFR 1926.302(c)(1)).

How far from the fueling spot do you start a chainsaw?

The logging standard says the chain saw shall be started at least 10 feet from the fueling area (29 CFR 1910.266(e)(2)(v)), and fueled at least 10 feet from any open flame or other source of ignition (29 CFR 1910.266(e)(2)(iv)).

Should a crew fell trees after this talk?

No. Felling, cutting wood under tension and work near power lines take training and equipment beyond a toolbox talk. Leave them to people trained and equipped for them.

Does OSHA require toolbox talks?

No rule requires a talk by that name. Construction employers must instruct each employee in the recognition and avoidance of unsafe conditions (29 CFR 1926.21(b)(2)), and many standards carry their own training duty; a toolbox talk is a common way to deliver part of it.

Do we need a sign-in sheet for a toolbox talk?

No general OSHA rule requires attendance records for a toolbox talk. Some standards require written certification of training, such as fall protection (29 CFR 1926.503(b)(1)) and forklift operators (29 CFR 1910.178(l)(6)). A signed sheet shows who attended; keep the topic, the date, the presenter and the language with it. It does not show that the content was understood.

Go further

More talks on machines, tools and energy

Sources

In a State Plan state, the state's own standard applies, and it can be stricter than the federal rule. Not legal advice.

All safety topics 100 safety topics Safety tip of the day