Skip to content

Urgent: Nov 20, 2026 — HCS 2024 Deadline. Get ready →

Machines, tools and energyAbout 5 minutes29 CFR 1926.304 · 1910.213

Table Saw Safety Toolbox Talk

A short talk on table saws: the hood guard, the spreader and anti-kickback fingers, what makes a board kick back, push sticks, where the operator stands, and why nobody reaches for scrap until the blade has stopped. In construction, each circular crosscut table saw and each hand-fed ripsaw shall be guarded by a hood over the blade (29 CFR 1926.304(h)(1) and (i)(1)).

All safety topics

At a glance

  • Construction: hoods on table saws (29 CFR 1926.304(h)(1) and (i)(1)); a lockable disconnect on fixed woodworking tools (29 CFR 1926.304(a)). General industry adds a spreader, nonkickback fingers and push sticks (29 CFR 1910.213).
  • About 5 minutes to read the script out loud, then the three questions. The drill and the tables below add time if you use them.
  • FY2025 citations: 29 CFR 1926.304, 108 (107 at construction sites); 29 CFR 1910.213, 458 (19 at construction sites).
  • Free PDF and Word file: the script, the questions, the rule and a 20-line sign-in sheet. No account, no email.

Read this to your crew

Today is the table saw. OSHA's woodworking guidance describes how operators get hurt: a hand that slips while feeding the board, hands held too close to the blade, reaching for scrap or finished pieces, and kickback, when the blade catches the board and throws it back toward the operator.

The hood over the blade stays on. It adjusts itself to the thickness of the board, stays in contact with it, and protects you from flying splinters and broken saw teeth.

Behind the blade, the spreader keeps the cut from squeezing the blade, and the anti-kickback fingers hold the board down if the saw kicks it back. If your saw has them, they stay on, set the way the manual shows.

Kickback is more likely when ripping than when crosscutting, and when the blade height is wrong, the blade is not maintained, safeguards are left off, or the lumber is poor. Use the right blade for the cut, keep it sharp, run the saw at the speed the manufacturer specifies, and guide the board parallel to the rip fence. Avoid crosscutting long boards on a table saw.

Keep your hands out of the line of the cut. Use a push stick for small pieces and to push the board past the blade. Support every piece: the cut and uncut ends, the scrap and the finished part.

Stand to the side of the blade, out of the path of a kickback, and keep people who are not part of the cut at a safe distance. Loose clothing, ties and jewelry can get caught in moving parts.

When the saw is switched off, stay at the saw until the blade stops turning, unless the saw has a brake that stops it. Scrap and finished pieces wait until the blade has stopped. Before changing the blade or adjusting the saw, disconnect it, or lock or tag its switch in the off position.

A cracked blade comes out of service, and eye protection goes on against chips, splinters and broken teeth.

Three questions for the crew

  1. If a board kicks back, where does it go, and where do you stand?
    Listen for: Back toward the operator, so the operator stands to the side of the blade.
  2. When do you use a push stick?
    Listen for: For small pieces and to push the board past the blade, so hands stay out of the line of the cut.
  3. The saw is switched off. When can you reach for the scrap?
    Listen for: Once the blade has stopped turning. For a blade change or an adjustment, the saw is disconnected, or its switch locked or tagged off.

What are OSHA's rules for table saws?

In construction, each circular crosscut table saw shall be guarded by a hood that meets the requirements for ripsaw hoods (29 CFR 1926.304(h)(1)), and each circular hand-fed ripsaw shall be guarded by a hood that completely encloses the part of the saw above the table and above the material being cut, adjusts itself to the thickness of the material, and protects the operator from flying splinters and broken saw teeth (29 CFR 1926.304(i)(1)).

All fixed power driven woodworking tools shall be provided with a disconnect switch that can either be locked or tagged in the off position (29 CFR 1926.304(a)).

In general industry, each hand-fed circular ripsaw shall also be furnished with a spreader (29 CFR 1910.213(c)(2)) and provided with nonkickback fingers or dogs (29 CFR 1910.213(c)(3)), and push sticks or push blocks shall be provided at the work place in the sizes and types suitable for the work (29 CFR 1910.213(s)(9)).

The paragraphs, word for word:

“(h) Hand-fed crosscut table saws. (1) Each circular crosscut table saw shall be guarded by a hood which shall meet all the requirements of paragraph (i)(1) of this section for hoods for circular ripsaws.”

29 CFR 1926.304(h)(1)

“(a) Disconnect switches. All fixed power driven woodworking tools shall be provided with a disconnect switch that can either be locked or tagged in the off position.”

29 CFR 1926.304(a)

How often did OSHA cite these rules in FY2025?

StandardConstruction sitesOther industriesAll FY2025 citations
29 CFR 1926.304Woodworking tools, constructionParagraph 1926.304(i): 16 of these1071108
29 CFR 1910.213Woodworking machinery, general industryParagraph 1910.213(c): 266 of these19439458

Citation items under 29 CFR issued Oct 1, 2024 to Sep 30, 2025, at federal and State Plan inspections, counted by HazComFast on U.S. Department of Labor enforcement data (extracted Oct 13, 2026). Construction means an inspection whose NAICS code starts with 23. The counts describe inspected establishments, not every employer.

Before each cut

CheckReadyStop and fix
Hood guardIn place, adjusting to the board and resting on itRemoved, tied up or stuck
Spreader and anti-kickback fingersInstalled as the saw's manual showsMissing, bent or set aside
BladeThe right blade for the cut, sharp, at the correct heightA crosscut blade used for ripping, a dull blade, or a cracked one
Push stick or push blockAt the saw, sized for the workHands would come near the line of the cut
SupportEvery piece supported: cut and uncut ends, scrap, finished partA board that would drop off the table
Operator positionTo the side of the bladeStanding in line with the blade

From OSHA's woodworking guidance for table saws. The manual of the saw in front of you covers its own guard and parts.

Drill: walk through a cut with the saw disconnected

About five minutes. The saw stays unplugged, or its switch locked off, for the whole drill.

  1. Set up a real cut from today's work.
  2. The operator shows the path of both hands from start to finish, with the push stick, without the blade turning.
  3. The operator shows where to stand: to the side of the blade. The crew points to where a kickback would go, back toward the operator in line with the blade, and agrees that nobody stands there.
  4. Name where the scrap and the finished piece will end up, and when they get cleared: once the blade has stopped.
  5. Check the hood, the spreader and the anti-kickback fingers against the manual.

Inside HazComFast

Give the table saw talk, keep every signature

Print this talk for the morning meeting. In HazComFast, the crew signs the toolbox talk on a phone, in English or Spanish, and the record stays with each worker.

  • Signed where the signal isn't

    In a basement or a dead zone, the crew can still sign the toolbox talk in Chrome on Android or on a computer. The sign-ins go out once the app is open with a signal again, and each one lands once.
  • Sheets and certificates in Spanish

    Toolbox talk PDFs and training certificates print in Spanish, and compliance reports come out in English, Spanish or both side by side.
  • Thirty hires on a Monday morning

    Import a spreadsheet, see line by line who was created and who wasn't, and print one sheet of QR badges for the morning toolbox talk. Email is optional.
  • Records that stay when a worker leaves

    When a worker leaves, their training records and competent person designation stay on file. The account can't take them along.

New sign-ups are paused · the free tools need no account

Questions about this talk

Does OSHA require a blade guard on a table saw?

Yes. In construction, each circular crosscut table saw shall be guarded by a hood (29 CFR 1926.304(h)(1)), and each hand-fed ripsaw shall be guarded by a hood over the saw above the table and the material (29 CFR 1926.304(i)(1)). General industry has its own hood rules in 29 CFR 1910.213.

What causes kickback on a table saw?

OSHA's woodworking guidance lists a blade at the wrong height, a blade that is not properly maintained, safeguards that are not used, and poor-quality lumber, and notes that kickbacks are more likely when ripping than when crosscutting. A spreader keeps the material from squeezing the saw, and anti-kickback fingers hold the stock down if it kicks back.

Are push sticks required?

In general industry, push sticks or push blocks shall be provided at the work place in the several sizes and types suitable for the work to be done (29 CFR 1910.213(s)(9)). OSHA's woodworking guidance says to use a push stick for small pieces of wood and for pushing stock past the blade.

When can you reach for scrap on a table saw?

After the blade stops turning. OSHA's woodworking guidance notes that operators are also hurt when removing scrap or finished pieces from the table, and suggests a brake that stops the blade from coasting, or having the operator stay at the saw until the blade stops.

Does this talk qualify someone to run a table saw?

No. The talk reminds the crew of the main hazards. Running a table saw safely takes instruction on that saw and practice with it.

Does OSHA require toolbox talks?

No rule requires a talk by that name. Construction employers must instruct each employee in the recognition and avoidance of unsafe conditions (29 CFR 1926.21(b)(2)), and many standards carry their own training duty; a toolbox talk is a common way to deliver part of it.

Do we need a sign-in sheet for a toolbox talk?

No general OSHA rule requires attendance records for a toolbox talk. Some standards require written certification of training, such as fall protection (29 CFR 1926.503(b)(1)) and forklift operators (29 CFR 1910.178(l)(6)). A signed sheet shows who attended; keep the topic, the date, the presenter and the language with it. It does not show that the content was understood.

Go further

More talks on machines, tools and energy

Sources

In a State Plan state, the state's own standard applies, and it can be stricter than the federal rule. Not legal advice.

All safety topics 100 safety topics Safety tip of the day