A strong sample can come from a deposit that does not qualify as Type A. The sample may be cohesive and resist penetration while the exposed ground is fissured, previously disturbed or affected by traffic vibration. The test result answers one part of the classification question.
Appendix A to 29 CFR 1926 Subpart P excludes five conditions from Type A soil. A cohesive strength reading of 1.5 tons per square foot or greater does not override those exclusions.
This distinction matters when the selected protective system depends on soil classification. It also matters when conditions change after the first assessment. The competent person needs enough information about the deposit and its surroundings to identify those changes, not merely a favorable number on a form.
Check when the Appendix A system applies
Appendix A(a)(2) describes its application to sloping or benching under 1926.652(b)(2), timber shoring under Appendix C, aluminum hydraulic shoring under Appendix D, and other systems whose selected data depend on this classification system. Determine the applicable design or selection method before using a soil label as a design input.
Protective systems selected through manufacturer data or another permitted method have their own conditions under 1926.652. A classification entry does not expand the system's rated limits. Design or select the protective system using the applicable method and its full requirements.
For the broader protection, access and inspection duties, use the trenching and excavation guide. The focus here is the Type A decision under Appendix A, particularly the conditions that a strength measurement cannot resolve.
Read the whole Type A definition
29 CFR 1926 Subpart P, Appendix A(b) describes Type A soil as cohesive soil with unconfined compressive strength of 1.5 tsf or greater, and gives examples. It then excludes five conditions. The exclusions address the ground's behavior and site conditions that a sample's strength does not establish.
| Condition excluding Type A | What the competent person needs to examine |
|---|---|
| Fissured soil | Cracks and breaks that affect the deposit's integrity |
| Vibration from heavy traffic, pile driving or similar effects | Sources of vibration affecting the excavation |
| Previously disturbed soil | Earlier excavation, filling or other evidence of disturbance |
| A qualifying sloped, layered system | Direction and inclination of layers entering the excavation |
| Other factors requiring less stable classification | Conditions affecting stability that remain relevant beyond the named examples |
Under the definition in 29 CFR 1926 Subpart P, Appendix A(b), finding one exclusion is enough to rule out Type A. It does not automatically establish the final alternative classification; read the Type B and Type C definitions against the actual conditions.
Case 1: strong clay with fissures
Take a cohesive deposit with a strength result above 1.5 tsf and visible cracks. The cracks cannot be ignored because the sample passed a strength threshold. 29 CFR 1926 Subpart P, Appendix A(b) expressly excludes fissured soil from Type A.
The Type B definition includes soil meeting Type A strength or cementation requirements that is fissured or subject to vibration. Other features may still put the material within Type C. For example, freely seeping water is a separate Type C characteristic under Appendix A(b). The competent person needs to assess the deposit, not stop after finding the first plausible category.
Record the observed fissures and the location represented by the analysis. A note reading only “1.7 tsf, Type A” would omit the condition deciding the classification. Recording the finding is a recommended way of preserving the assessment's basis; 29 CFR 1926 Subpart P, Appendix A(c) establishes the evaluations needed, without prescribing that particular note format.
In a field note, identify where each observation came from. “Fissures on the north wall beside the utility crossing” gives the next competent person a place to examine. “Soil okay” leaves both the condition and its location unknown. A sketch can show where the excavation crosses fill and undisturbed ground. This is a suggested handoff practice, not a prescribed OSHA note format.
Case 2: an intact sample beside a traffic route
At another excavation, the exposed material appears cohesive and intact, but heavy vehicles travel along a nearby route. Determine whether the deposit is subject to vibration from that traffic. The Type A exclusion in Appendix A(b) concerns the vibration affecting the material, not whether the sample looked intact when removed.
The regulation supplies no universal distance from a road that settles this classification. A checklist based on distance alone cannot resolve it. The competent person needs to examine the vibration source and decide how the site conditions affect the deposit.
Conditions can change during the job. Moving a haul route or beginning a vibration-producing operation can affect the information on which classification was based. 29 CFR 1926 Subpart P, Appendix A(c)(5) requires evaluation of changes affecting classification and reclassification as necessary. A daily inspection under 1926.651(k)(1) is a separate opportunity to identify conditions requiring that response.
Case 3: the trench crosses an old utility cut
A current excavation may pass through ground that was opened and backfilled years earlier. Compacted backfill can feel firm. Firmness does not erase previous disturbance, which excludes Type A under Appendix A(b).
Previously disturbed soil is included in the Type B definition except where the soil would otherwise meet Type C. Look for the actual condition of the fill, water and material. Neither “all backfill is Type B” nor “old work no longer counts” follows from the text of 29 CFR 1926 Subpart P, Appendix A(b).
The excavation may contain more than one deposit. The competent person's classification needs to represent what workers will encounter. An analysis from intact ground at one end does not establish the properties of the old cut elsewhere. Appendix A(c)(3) calls for the visual and manual evaluations to supply sufficient quantitative and qualitative information about the properties and conditions affecting classification.
Case 4: layers dip into the excavation
Layered ground calls for attention to geometry as well as material strength. The Type A definition excludes a sloped, layered system where layers dip into the excavation on a slope of four horizontal to one vertical or greater. The Type C definition also addresses layers dipping toward the excavation at 4H:1V or steeper. Read those provisions together under 29 CFR 1926 Subpart P, Appendix A(b).
Appendix A(c)(4) generally classifies a layered system according to its weakest layer. It also permits individual classification where a more stable layer lies beneath a less stable one. That exception needs the actual layer arrangement; it is not permission to use the strongest sample for the whole face.
Have the competent person identify the direction and inclination of the layers. A drawing may communicate that finding better than an unexplained category. The applicable protective-system method under 1926.652 then needs to be selected using the relevant conditions and data. Do not derive a permitted benching layout from this simplified field case.
Case 5: a condition outside the four named examples
The fifth Type A exclusion in 29 CFR 1926 Subpart P, Appendix A(b) addresses other factors requiring classification as a less stable material. It prevents the first four exclusions from becoming an exhaustive site-hazard checklist. A competent person still has to recognize the conditions influencing the deposit.
Water provides an important cross-check. Appendix A(b) places submerged soil and soil with freely seeping water in Type C. A favorable dry sample cannot establish that an entire wet deposit is Type A. Water-related excavation hazards also require their own evaluation under 1926.651(h).
If circumstances change, evaluate them under 29 CFR 1926 Subpart P, Appendix A(c)(5). Reclassification is called for as necessary to reflect those changed circumstances. There is no rainfall quantity in that paragraph that authorizes a delay while a crew waits for a threshold to be reached.
Combine visual and manual evaluations
Appendix A(c)(2) calls for a minimum of one visual and one manual analysis for this classification system. These are complementary sources of information. A manual strength estimate does not identify every fissure, vibration source or layer arrangement. A visual inspection does not replace the manual analysis needed by the appendix.
Appendix A(d) describes acceptable visual and manual approaches. Select evaluations capable of establishing the properties and conditions relevant to the deposit. The competent person needs to interpret the results against the deposit and site conditions. A pocket-instrument reading or photograph alone cannot supply all of that information.
Distinguish cohesive strength thresholds from granular-soil definitions. 29 CFR 1926 Subpart P, Appendix A(b) places specified granular materials in Type B or Type C by description. Applying a cohesive-strength threshold indiscriminately to sand or gravel does not follow those definitions.
Keep classification tied to the inspection
Under 1926.651(k)(1), a competent person inspects excavations, adjacent areas and protective systems before work and as needed throughout the shift, with inspections after rainstorms and other hazard-increasing occurrences when employee exposure can reasonably be anticipated. Classification conditions can be part of what those inspections reveal.
Where 1926.651(k)(2) applies, exposed employees must be removed from the hazardous area until the necessary precautions have been taken. Updating the category on a screen is not the protective action itself. The competent-person designation guide explains the authority component of that role.
Use the protective-system selection tool as an organizing aid, with competent-person assessment and applicable system data. Keep the classification basis beside the protection decision. The trench geometry analysis can help explain the space a slope consumes, but its arithmetic cannot establish your soil type.
Before a crew enters, ask the competent person what could invalidate the current classification. The answer should refer to the deposit and the conditions observed today. Keep that explanation available to the supervisor who takes over the next shift.
Frequently Asked Questions
Does a strength of 1.5 tsf make a soil Type A?
Not by itself. Appendix A(b) to 29 CFR 1926 Subpart P describes Type A cohesive strength of 1.5 tsf or greater, then lists five conditions that exclude Type A classification. The competent person needs to consider the whole definition.
Can previously disturbed soil be Type A?
No. 29 CFR 1926 Subpart P, Appendix A(b) excludes previously disturbed soil from Type A. Its Type B definition includes previously disturbed soil except soil that would otherwise be Type C.
How many tests does OSHA call for in classification?
When applying the classification system in 29 CFR 1926 Subpart P, Appendix A, paragraph (c)(2) calls for a minimum of one visual and one manual analysis by a competent person. Paragraph (c)(3) calls for enough information to identify the properties and conditions affecting the deposit.
Does soil classification have to change after conditions change?
29 CFR 1926 Subpart P, Appendix A(c)(5) requires a competent person to evaluate changes affecting classification and reclassify as necessary. The inspection duties in 1926.651(k) apply separately, including after rainstorms or other hazard-increasing events when employee exposure can reasonably be anticipated.
Site-wide regulatory figures such as compliance dates and penalty amounts come from our regulatory source-of-truth modules, last checked against the eCFR, OSHA.gov, and the Federal Register on October 19, 2026. Last reviewed November 15, 2026.
About This Article
Published by: HazComFast
Published: November 15, 2026
Last Updated: November 15, 2026
This content is for informational purposes only and does not constitute legal advice.
