Construction · CAS Database
Crystalline Silica
Crystalline Silica (CAS 14808-60-7) — Component of sand and concrete. What OSHA's HazCom rules ask of it on a job site, and where its Safety Data Sheet comes from: your supplier.
Verified vs OSHA sources · October 19, 2026
CAS Registry Number CAS 14808-60-7 · also known as Quartz, SiO2, Silicon dioxide
Overview
Component of sand and concrete
Crystalline Silica on the job site
Respirable crystalline silica is the invisible hazard of concrete and masonry work: cutting, grinding, drilling, tuck-pointing, and abrasive blasting all release particles small enough to reach deep lung tissue, where they cause irreversible silicosis and raise lung-cancer risk. The 50 µg/m³ PEL and 25 µg/m³ action level are eight-hour averages, and a single hour of dry cutting can blow past them.
OSHA's construction silica rule (1926.1153) lets most crews skip air monitoring by following Table 1 — pairing each task with a specified control, almost always water (wet cutting) or a HEPA-filtered dust extractor on the tool, plus the right respirator for that task. The classic failure is dry-cutting a few cuts “just this once” without water or vacuum; the dust that hangs in the air is exactly the fraction that does the damage. A written exposure control plan and a competent person to run it are required.
Key takeaways
- Dry cutting can produce dust well above the 50 µg/m³ PEL, depending on the tool, material and ventilation — the fine, lingering dust is the dangerous fraction.
- Follow Table 1 (water or on-tool HEPA vacuum + the right respirator) to comply without air monitoring.
- A written exposure control plan and a competent person are required by 1926.1153.
Field guidance for planning and training — not a substitute for the manufacturer Safety Data Sheet, which gives the exposure limits, PPE, and handling for your specific product.
OSHA Exposure Limits
OSHA permissible exposure limit (PEL) and secondary limit for Crystalline Silica on a US construction site. Where a substance-specific 1926 standard applies, its codified limit is shown; otherwise the figure comes from Table 1 to 29 CFR 1926.55, the construction air-contaminants table. Where Table 1 gives no figure, either the substance has its own standard (the row says "see 1926.xxxx" and this page names that standard) or Table 1 sets no limit for it. In both cases Section 8 of the Safety Data Sheet lists the limits other bodies recommend and the supplier's controls.
| Limit | Value | Basis / citation |
|---|---|---|
| OSHA PEL (8-hr TWA) | 50 µg/m³ | 29 CFR 1926.1153 |
| Action level | 25 µg/m³ | Triggers exposure monitoring / medical surveillance |
| Averaging period | 8-hour TWA | Compare with ACGIH TLV / NIOSH REL — often more protective than the OSHA PEL |
Many OSHA PELs date to 1971 and may be less protective than current ACGIH/NIOSH values; always check Section 8 of the manufacturer SDS for the limits it lists, which can be lower than the PEL, and for its control guidance. Not legal advice.
GHS Classification
Physical Properties
Where Crystalline Silica shows up on the job
Trades that commonly handle Crystalline Silica, each with an OSHA HazCom guide built for the chemicals and tasks on that kind of site:
OSHA & HazCom Compliance Requirements
For construction work, Hazard Communication is governed by 29 CFR 1926.59 (adopts 29 CFR 1910.1200). Employers who use Crystalline Silica must:
- •Maintain an accessible SDS for Crystalline Silica (readily accessible during each work shift, 29 CFR 1910.1200(g)(8))
- •Keep the supplier's label on shipped containers (29 CFR 1910.1200(f)(1)) and mark workplace containers with the shipped-label elements or the product identifier and hazard information (29 CFR 1910.1200(f)(6)); a portable container for immediate use by the person who filled it needs none (1910.1200(f)(8))
- •Include it in the workplace chemical inventory
- •Train employees on hazards before initial assignment
- •Retain employee exposure and medical records per 29 CFR 1910.1020 — 30-year retention applies to exposure/medical records, not to SDSs generically
Substance-specific standard: Respirable Crystalline Silica
In addition to HazCom, this chemical is regulated under 29 CFR 1926.1153. 8-hour TWA PEL of 50 µg/m³, action level 25 µg/m³. Common in concrete cutting, grinding, drilling, and abrasive blasting. Medical surveillance is required to use a respirator 30+ days/year (1926.1153(h)(1)(i)).
Respirable crystalline silica has its own section in Subpart Z of 29 CFR 1926 (1926.1153). The limits and what each standard requires, side by side: OSHA substance-specific standards.
HazCom (1910.1200 / construction 1926.59) covers hazard classification, labels, SDSs, the written program (with its chemical list and the rules for non-routine tasks and multi-employer sites) and training. It does not impose chemical storage segregation. Flammable & combustible liquid storage for construction is 29 CFR 1926.152; segregation of incompatibles is planned from SDS Sections 7 and 10. Not legal advice; state-plan states may have stricter rules.
Handling & Secondary-Container Labeling
When you transfer Crystalline Silica into a workplace (secondary) container, OSHA gives two compliant options under 29 CFR 1910.1200(f)(6):
- •(f)(6)(i): full GHS label elements (as on the shipped container)
- •(f)(6)(ii): product identifier + words/pictures/symbols (or combination) that provide AT LEAST general information on the hazards and, with the other information immediately available under the HazCom program, the specific hazards
There is no volume/size cutoff for secondary containers — the ≤100 ml / ≤3 ml accommodations (29 CFR 1910.1200(f)(12) (added by the HCS 2024 final rule)) apply only to the manufacturer's shipped container. A portable container filled for the immediate use of the worker who fills it needs no label (29 CFR 1910.1200(f)(8)).
GHS Hazard Classification under OSHA HCS
OSHA's Hazard Communication Standard adopts the GHS (primarily GHS Revision 7 (HCS 2024)). It requires 8 hazard pictograms (Appendix C, Figure C.1). The Environment pictogram (GHS09) is not required by OSHA — Not in App C; outside OSHA jurisdiction; voluntary.
The 8 OSHA-required pictograms:
For flammable liquids, OSHA classifies by flash point and boiling point (App B.6.1 / 1910.106(a)):
- •Category 1: FP < 73.4°F AND BP <= 95°F
- •Category 2: FP < 73.4°F AND BP > 95°F
- •Category 3: FP >= 73.4°F AND <= 140°F
- •Category 4: FP > 140°F AND <= 199.4°F
The specific GHS classification of Crystalline Silica comes from its Safety Data Sheet (Section 2). Use the live classification panel above and the manufacturer SDS to confirm pictograms and categories.
HCS 2024 Update Deadlines
Under the federal Hazard Communication Standard 2024 update (aligned primarily GHS Revision 7):
- •May 19, 2026 — manufacturers, importers, and distributors update substance labels & SDSs (1910.1200(j)(2)(i))
- •November 20, 2026 — employers, as necessary, update alternative workplace labels, the written program & training for newly identified hazards (1910.1200(j)(2)(ii))
During the interim, parties may comply with the 2012 HCS, the 2024 HCS, or both. These are the federal OSHA dates; State Plans adopt the update on their own schedules, so check your state.
Quick Actions
Put Crystalline Silica on your written inventory, print the workplace label your containers need, and keep your supplier’s sheet reachable on the jobsite.
The safety data sheet for your product comes from the supplier who sold it to you — no public registry can provide it. For the underlying chemistry, the public record is on PubChem.
Where this fits in your HazCom program
- SDS management — collecting the sheet, keeping it current, and making it readable during each work shift.
- GHS labels & workplace labeling — what has to appear on the shipped container, and what a secondary container needs instead.
Free Compliance Tools for Crystalline Silica
Also on a concrete & masonry job
Frequently Asked Questions
What is Crystalline Silica (CAS 14808-60-7)?
Component of sand and concrete
What are the OSHA HazCom requirements for Crystalline Silica on a construction site?
For construction work, Hazard Communication is governed by 29 CFR 1926.59 (adopts 29 CFR 1910.1200). Where a product you use containing Crystalline Silica is a hazardous chemical under the standard (its supplier's label and SDS say so), you must keep its Safety Data Sheet accessible, keep the supplier's label on shipped containers and label workplace containers under (f)(6), list it in the written program's chemical inventory, and train workers on its hazards at initial assignment. Exemptions apply, such as a consumer product used the way a consumer would use it (1910.1200(b)(6)(ix)).
Is there a substance-specific OSHA standard for Crystalline Silica?
Yes. In addition to HazCom, Respirable Crystalline Silica is regulated under 29 CFR 1926.1153. The 8-hour TWA permissible exposure limit (PEL) is 50 µg/m³, with an action level of 25 µg/m³. 8-hour TWA PEL of 50 µg/m³, action level 25 µg/m³. Common in concrete cutting, grinding, drilling, and abrasive blasting. Medical surveillance is required to use a respirator 30+ days/year (1926.1153(h)(1)(i)).
What is the OSHA permissible exposure limit (PEL) for Crystalline Silica?
OSHA's 8-hour time-weighted-average PEL for Respirable Crystalline Silica is 50 µg/m³, with an action level of 25 µg/m³ (29 CFR 1926.1153). Confirm the exposure limit applicable to your task against Section 8 of the manufacturer Safety Data Sheet.
When does the updated HCS 2024 labeling apply to Crystalline Silica?
Under the federal Hazard Communication Standard 2024 update (aligned primarily GHS Revision 7), manufacturers, importers and distributors must comply by May 19, 2026 when Crystalline Silica is sold as a substance, and by November 19, 2027 for mixtures that contain it. Employers must, as necessary, update alternative workplace labels, the written program and training for newly identified hazards by November 20, 2026 for substances and May 19, 2028 for mixtures (29 CFR 1910.1200(j)). During the interim, parties may comply with the 2012 HCS, the 2024 HCS, or both. State Plans adopt the update on their own schedules, so check your state's dates.
How do I label a secondary (workplace) container of Crystalline Silica?
Under 29 CFR 1910.1200(f)(6) you have two options: (i) the label elements of (f)(1)(i) through (v): product identifier, signal word, hazard statements, pictograms and precautionary statements, with no supplier name or address needed, or (ii) the product identifier plus words, pictures, symbols, or a combination that provide at least general hazard information and that, with the other information immediately available to workers under the HazCom program, give the specific hazards. There is no volume/size cutoff for secondary containers. A portable container filled from a labeled container, kept under the control of the worker who fills it and used only by that worker within the same shift, does not require a label (29 CFR 1910.1200(f)(8)).
How long must SDS and exposure records for Crystalline Silica be kept?
Under 29 CFR 1910.1020, 30-year retention applies to employee exposure and medical records (medical records: duration of employment plus 30 years) — not to SDSs generically. Where an SDS is not retained, a record of the chemical's identity, where it was used, and when must be kept for at least 30 years.
Where can I find the SDS for Crystalline Silica?
Under 29 CFR 1910.1200(g)(6) and (g)(7), the manufacturer or importer of Crystalline Silica must ensure that distributors and employers receive its Safety Data Sheet with the initial shipment and with the first shipment after the sheet is updated, and a distributor passes it on in its commercial shipments the same way. Retail and wholesale distributors that sell to employers over the counter or to commercial accounts have their own duties in (g)(7)(iii) to (vii), such as providing the sheet on request. HazComFast keeps the sheets you collect in one inventory per jobsite, searchable by product, manufacturer or CAS number, and your jobsite's SDS load onto the phone on their own.
Sources & Primary References
Regulatory data on this page is sourced from HazComFast's verified regulatory module (29 CFR 1926.59 / 1910.1200 and substance-specific 1926 standards), last verified October 19, 2026 against eCFR, OSHA.gov, and the Federal Register. Physical-property data comes from PubChem. Confirm it against the manufacturer Safety Data Sheet. This page is informational and is not legal advice.
Get the Binder in Order Before the Inspector Arrives. Are You Ready?
OSHA inspections come unannounced, apart from the few exceptions listed in 29 CFR 1903.6. Get the binder in order before the opening conference, not during it.
Serious Violation
$16,550
per violation (max)
HazComFast Pro
$199/mo
10 jobsites, unlimited chemicals, unlimited workers
New sign-ups are paused. The free tools below need no account, and customers can log in as usual.
Your account keeps working as usual. Cancel anytime.