Skip to content

Urgent: Nov 20, 2026 — HCS 2024 Deadline. Get ready →

Safety

Risk matrix template for workplace hazard assessments

By HazComFastPublished November 16, 20266 min read
HazComFastLast reviewed November 16, 2026

A risk matrix records the severity and likelihood assigned to a hazardous event. Use it to prioritize corrective work and explain the reasoning behind a decision. Keep the task, evidence and controls with the score.

This worksheet uses a 5 × 5 matrix, with severity multiplied by likelihood. The scales are an example assessment method, not OSHA-mandated categories or measured probabilities. Applicable safety requirements remain part of the assessment regardless of the score.

Describe the hazardous event

Identify the task, the event and the people who could be harmed. For chemical work, that means describing the release or contact, its route and the conditions under which it could occur. Include equipment condition, duration, frequency and existing controls.

Use observations, SDSs, equipment information, exposure data and input from employees who do the work. Record gaps that could change the decision.

OSHA's hazard identification guidance recommends considering severity and likelihood when prioritizing hazards and addressing serious conditions promptly.

Severity scale

Rate the credible consequence of the event being assessed. Consider the exposure and failure mechanism, including severe outcomes even when earlier incidents caused only minor harm.

LevelDescription used in this worksheet
1 (Minor)Temporary harm requiring only basic first aid, with no lasting impairment.
2 (Moderate)Reversible harm requiring treatment, with recovery expected without prolonged impairment.
3 (Serious)Serious injury or illness with prolonged recovery or substantial temporary impairment.
4 (Permanently disabling)Lasting loss of function or permanent disability.
5 (Fatal)One or more fatalities.

These descriptions serve this assessment method. Use OSHA's separate recordkeeping criteria when determining whether an injury or illness is recordable.

If the event has materially different outcomes, assess the scenarios separately. State which consequence supports each rating.

Likelihood scale

Assess likelihood for the task conditions and controls documented in the same record. Consider exposure opportunities, failure history, equipment condition and the reliability of controls.

Define the assessment basis: one execution of the task, a work phase or another stated period. Use a consistent basis when comparing assessments. The chance of an event during one operation and its chance across a year of repeated operations answer different questions.

LevelDescription used in this worksheetBasis to document
1 (Remote)Credible but judged very unlikely under the assessed conditions.Evidence supporting effective controls and the failure sequence needed for the event.
2 (Unlikely)Could occur under a foreseeable failure or abnormal condition.The failure or deviation considered and the controls that reduce its likelihood.
3 (Possible)Could occur during the assessed work.Exposure opportunities and reasons the existing controls leave a credible event.
4 (Likely)Expected during the work unless conditions or controls improve.Observed weaknesses, repeated deviations or other supporting evidence.
5 (Almost certain)The event is expected under the assessed conditions and period.Current observations, recurrence or other evidence supporting that expectation.

These are qualitative judgments. Document why a level fits the scenario; the table supplies no numerical probability.

Where information is insufficient, record likelihood unresolved and identify what needs to be established. Treat the uncertainty as a decision issue before the task proceeds.

The 5 × 5 risk matrix

Score = severity × likelihood

Severity / likelihood1 (Remote)2 (Unlikely)3 (Possible)4 (Likely)5 (Almost certain)
5 (Fatal)510152025
4 (Permanently disabling)48121620
3 (Serious)3691215
2 (Moderate)246810
1 (Minor)12345

Retain severity and likelihood alongside their product. Severity 5 with likelihood 1 and severity 1 with likelihood 5 both produce a score of 5, but call for different decisions about consequences and controls.

Set action rules before ranking the work

Define who can authorize work and who needs to resolve outstanding findings. Establish any score bands within the organization's method and explain their action rules.

Apply these checks to every assessment:

  • Immediate danger: protect affected people and take the necessary action before continuing the assessment.
  • Unmet requirement: install the needed safeguard or meet the applicable provision before relying on a score.
  • Fatal or permanently disabling consequence: call for explicit review of the failure scenario and controls, including a low-likelihood rating.
  • Missing evidence: identify the decision owner and resolve information that could change the work decision.
  • Control failure: address the failed control and reassess the task.

A score can order a corrective-action list. It cannot waive a guarding, isolation, exposure-control or permit requirement.

Select controls and verify them

Consider elimination and substitution before engineering controls, administrative measures and personal protective equipment (PPE). NIOSH's hierarchy of controls explains that order.

Describe the control in terms of the event. Record what equipment or process changes, who carries out the procedure and how the change reduces exposure or prevents failure.

Calculate a proposed residual rating for planned controls only as a planning estimate. Verify installation and effectiveness before treating that estimate as the current risk. Where PPE is selected, account for its limitations, fit and use.

Risk assessment worksheet

FieldAssessment entry
Employer, site and assessment date____________________
Task, equipment or process____________________
Hazardous event and people exposed____________________
Assessment period or exposure-opportunity basis____________________
Credible consequence____________________
Conditions and existing controls____________________
Evidence and employee input____________________
Assumptions and missing information____________________
Current severity and reason____________________
Current likelihood and reason____________________
Current score____________________
Applicable requirements and outstanding safeguards____________________
Immediate-action or severe-consequence finding____________________
Selected controls and expected effect____________________
Action owner and deadline____________________
Interim protection and work restrictions____________________
Evidence of implementation____________________
Verification method, date and result____________________
Verified residual severity and likelihood, with reasons____________________
Verified residual score____________________
Work decision and authorized decision owner____________________
Review date and reassessment triggers____________________

The job hazard analysis builder can organize task steps and controls. Attach the matrix to the assessment for the task so the reasoning and action owner remain available.

Check the control at the workplace

Define what will be observed, measured or tested, then record who checked it and under which conditions. For an exposure control, verify the exposure-related result; for an interlock or other safeguard, use a suitable functional check.

Keep an action open when verification fails. Update the work restrictions and assessment to reflect the actual condition. The incident investigation form can support the evidence and corrective-action record when the finding follows an incident.

When to reassess

Reassess after a change affecting the event or controls: a new product, machine, layout, procedure, exposure result or employee assignment. An incident, near miss or failed safeguard may also invalidate the earlier judgment.

Retain the previous assessment and explain the changed evidence or conditions. That record helps distinguish a reduction in risk from a change in scoring judgment.

Frequently Asked Questions

Is a 5 × 5 matrix needed for a job hazard analysis?

OSHA has no general requirement for this particular table in every JHA. Choose a method that identifies the work's hazards, supports effective controls and addresses the standards governing the task.

How should a team resolve different scores?

Compare the event descriptions, consequences, evidence and controls first. Different assumptions often explain different ratings. Record unresolved disagreement for the decision owner rather than averaging scores that describe different scenarios.

Last reviewed November 16, 2026.

About This Article

Published by: HazComFast

Published: November 16, 2026

Last Updated: November 16, 2026

This content is for informational purposes only and does not constitute legal advice.

Ready to simplify your HazCom compliance?

HazComFast keeps your SDS library, GHS labels, and training records audit-ready, with the jobsite's SDS on the crew's phones.